BIOklar move 8

Catalogue index: L-F146AN

  • In stock
  • English name:
  • Art.No.:
  • EAN code:
  • Producer:
  • Quantity in a box:
    • 0
Original name:

Description

BIOklar move 8
pond filter

 

BlOklar MOVE is a version of the well-known and tested in thousands of ponds filter BlOklar, but followed in the third chamber technology of the floating bed "moving bed" instead contribution Aquarock. This is an increasingly popular method of filtering based on the filter medium which is Kaldnes .
They are small plastic shapes with specific gravity similar to water , floating freely in the water depth and with a very large biologically active surface Water in the filter chamber is constantly put into motion with the air fed from below so that the whole mass of Kaldnes was in motion and dead zones were not formed In oxygen saturated water, on Kaldnes fittings biologically active membrane works much more intensively than on other static filtration media.

Thanks to the existence of a zone of "young" membrane outside the fittings, permanently cut and "old" from the inside, the nitrification process runs more fully and without danger of anaerobic zones. For the filter, simply connect the supplied air pump and pour Kaldnes into the third chamber. The Kaldnes filter media does not require cleaning , however, you can remove dirt from the settler under the third filtration chamber, as in the case of the first two chambers.

It is made of polyester-glass laminate, thanks to which it is characterized by a very durable construction.
The filter provides a suitable biologically active surface, which is crucial in maintaining clean, clear water, and maintaining a proper biological balance in the pond, even with a large fish stocking.

A settler was used in each chamber, used to easily remove impurities from the filter and clean the filtration chambers. 
To make cleaning of such a filter easier and for greater control over the flow of water through the filter material, the filter is divided into two series connected in series.

 


The filter can be seen on the video: 


User's manual [pdf]


Technical data:  

Input: ø 25/32 / 40mm, output: ø 75 mm 
Settling tanks with drain valves: ø 50 mm

Recommended pump capacity: approx. 2,000 L / hl;  for example Pump EP 3500
Dimensions: 180x65x65 (H) cm 

Suitable for:
fishless  ponds with a capacity of up to 16,000 liters
- ponds with fish up to 8,000 liters
- ponds with koi carps with a capacity of up to 6,000 liters


Color: anthracite

In the set: Air pump ACO-2208

BIOklar filter table



Filter materials: 

I Chamber - filter brushes 
The pump from the pool pushes water into the first module, where it is directed to the bottom of the module. Here the stream of water slows down and the coarsest impurities precipitate.
The lower part of each chamber acts as a settler, from which the sediment can be easily removed by opening the valve located in the lowest part of the module.
Then, the water goes smoothly to the upper part of the tank, where there are special filter brushes, similar to those for washing bottles.
They work mainly mechanically, catching thicker suspensions.


II Chamber - Kaldnes .
The second module mainly serves the role of biological filtration. It is filled with floating plastic shapes that are an ideal habitat for nitrifying bacteria.



Filter cleaning is maximally simplified. Coarse cleaning is performed more frequently (every week) and involves removing impurities from settling tanks. One should open for a moment each of the 2 valves under each of the two modules, because there they sediment the thickest pollutants. A more thorough cleaning is performed by opening the valve in each of the settlers for a longer time, and when the water escapes from the module, move the brushes and the filter mat, causing the descent together with the water that escapes.
Wait until all the water leaves the individual chambers.


Attention!

BIOklar filters are also available in a gravitational version , in which water from the pond flows into the filter under the influence of gravity and after filtration through all materials is pumped out of the last chamber.

  • All filters can work in both pump and gravity versions.
  • Models 8, 15 and 200 are available as standard in the pump version, inlet in the upper part of the first chamber. On request, it is possible to make a gravity version - then the inlet at the bottom of the filter.
  • Models 30, 60, 120 and 140 are available as standard in both pump and gravity versions. Both versions have an inlet at the bottom of the filter, straight to the first sediment chamber.
  • When ordering a filter, please specify whether it is a pump or gravity version.
  • Transport costs (shipping on a pallet) are not included in the price of the Bioklar filter

Ask about product